Whether it is one fixture or the whole room, Pro Bathroom Remodeling plans and builds bathrooms in Bloomington with a crew of our own.
Design, permits and installation are managed by one team.
We plan Bloomington bathrooms around the room you have and the way your household uses it, not a catalog layout.
Projects involving plumbing changes, new electrical work or layout shifts are permitted through San Bernardino County Land Use Services – Building and Safety. The written scope lists waterproofing, fixtures and finishes before work starts.
No pressure, no obligation. We'll call to confirm your appointment window.
Each service below is performed for Bloomington homeowners by our in-house crew, with a planning price range for each service.
In Bloomington bathrooms, a tub replacement can be a quick swap or the start of a larger refresh around the wet wall.
Roughly 74% of the housing stock in Bloomington dates from before 1990, per Census ACS 2020–2024. Under California Civil Code Section 1101, a home built before 1994 should have water-conserving fixtures, and permitted remodeling is the point where that is reviewed; we price any swap alongside the tub.
We begin by measuring the opening and noting the drain side, since tubs are made for left or right drains. The old tub is cut or lifted out without damaging nearby walls where possible. A deeper soaking tub or a whirlpool needs a check of hot water supply and, for jets, a power source. We confirm floor framing, protect the drain during work and finish the surround with tile or panels that suit the budget. Debris from the old tub is hauled away as part of the written scope. Caulk joints are left to cure before the tub is filled for the first time.
Planning checklist
Expect about $1,300–$3,500 for the project in Bloomington. Standard to mid-range tub replacement, installed. Ultra-luxury stone tubs, commercial work and a full bathroom remodel are not included.


Updating a shower in Bloomington can mean new walls and glass only, or a full rebuild with a new pan, valve and drain.
West Valley Water District or another valley provider, depending on the parcel is the water provider in Bloomington. We use its published water quality report when selecting the valve, the head and the finish for a new shower.
The pan and the wall membrane do the real work in a shower; tile is mostly the finish. We slope the floor properly, seal every corner and penetration, and hold water in the pan for a test before tile goes in. We replace the valve with a pressure-balancing or thermostatic model, set niches between studs, and plan any bench or grab bar blocking before the walls close. Corner shelves can be built into the tile instead of added later. We match tile layout to the niche so grout lines align. We start by opening the old surround and checking studs, insulation and the existing pan for leaks. A curb height is chosen to hold water without being awkward to step over.
Checked before work begins
Plan on $4,500–$12,000 for the project in Bloomington. From a ready-made update through a custom tiled walk-in. Full-room gut remodels are excluded.
Turning a tub into a shower gives a Bloomington bathroom a lower step, more standing room and fewer surfaces to clean.
We remove the tub, check the floor and walls behind it, and decide on the drain position and curb height. The valve moves up to a standing height, and the floor is sloped and waterproofed before tile. We also look at the wall the valve sits on, since moving it can mean opening a closet or hallway on the other side. A wider glass opening makes cleaning and stepping in easier. If the alcove is long, a bench at one end can use the extra length. Grab bar blocking is set where you will actually reach when stepping in. Wall tile can run to the ceiling for a cleaner line in a former tub alcove.
The average household in Bloomington has 4 people, according to the Census. If one bathroom serves the whole family, converting the tub to a walk-in shower with a hand shower on a slide bar lets adults and kids use the same space comfortably.
The planning range in Bloomington is $3,500–$10,000 for the tub-to-shower conversion. Covers tub removal and a new shower, ready-made to common custom. Does not include wet-room extremes or a complete bathroom remodel.
Checked before work begins


Some Bloomington homes lost their only tub in an earlier remodel, and the owners now want one back for children or for soaking.
Tubs come in standard 60-inch alcove lengths and shorter 54-inch models for tight spaces. We measure the old stall to see which fits or whether a wall must move. The tub is set level, the drain is tested, and the walls are finished to keep water away from the framing. The old shower pan, walls and valve are removed first. A tub with an integral apron saves building a separate front panel. The floor is opened at the drain for the new trap. The tub's drain side is matched to the existing plumbing where possible. The valve moves down to tub height and a spout is added.
Census figures show about 69% of occupied homes in Bloomington are lived in by their owners. Owners who want a tub for bathing children or for a long soak get a model sized to the alcove and to the water heater that has to fill it.
Budget $2,600–$9,300 for the shower-to-tub conversion in Bloomington. Covers converting a shower to a tub with normal framing and plumbing changes. Major structural reinforcement and showpiece freestanding tubs are excluded.
Planning checklist
New flooring changes how a Bloomington bathroom looks and feels underfoot, and it is the right moment to fix what lies beneath.
NOAA 1991–2020 normals from the Riverside Municipal Airport station put the average daily low near 53°F, so heated floors are a comfort upgrade rather than a need. The bigger decisions are slip resistance near the shower and a flat, sound subfloor under the tile or plank.
A tile floor is only as good as what lies under it, so we fix squeaks and level dips before setting tile. A crack-isolation or uncoupling membrane helps protect tile on wood subfloors. Natural stone looks rich but needs sealing. Textured tile and smaller formats with more grout lines give better grip when the floor is wet. We remove the old floor and look for soft spots, loose boards or cracked slab. Grout color and width are chosen for cleaning ease as much as style. Matte finishes give better grip than polished ones when wet. On slabs we check for cracks that could transfer.
Before we start
The planning range in Bloomington is $8–$26 per square foot installed. Per-square-foot price for the finished floor, installed. Shower waterproofing and vanity work are priced separately.


In Bloomington, local rules decide where a dumpster or delivery truck can park. We sort that out before the cabinet is delivered and keep the old vanity in place until the new one is on site.
Vanity choices in Bloomington start with who uses the room and what needs to be stored there.
Vanity planning covers width, depth, height, storage and the sink and faucet together. We check where the drain and supplies come through so the cabinet layout works around them. Undermount sinks are easiest to wipe clean, while vessel sinks need a lower cabinet. Lights and mirrors are centered on the sinks once the cabinet position is fixed. Outlet location is checked so it sits clear of the sink and mirror. Soft-close hinges and slides are worth comparing between cabinet lines. Wall-mounted vanities need solid blocking between the studs. Quartz, granite, cultured marble and solid-surface tops each differ in maintenance and cost. Drawer bases suit tight rooms, since drawers are easier to reach than deep doors. We confirm the faucet holes in the countertop match the faucet chosen.
The planning range in Bloomington is $800–$3,000 per vanity installed. Covers a typical vanity with countertop and faucet connection. Custom cabinetry is excluded.
On our list
Under California code, receptacles in a bathroom need GFCI protection and fixtures close to the tub or shower must carry a damp or wet rating; CALGreen adds an exhaust fan with humidity control that vents to the outside. The Riverside Municipal Airport station records roughly 9.4 inches of precipitation a year, yet shower steam is the real load, so we match the fan to the room size and lay out vanity and shower lights in one plan.
Good lighting changes how a Bloomington bathroom works, from shaving and makeup to a safe trip at night.
LED fixtures run cool and use less power, and their color temperature can be chosen to suit the finishes. The exhaust fan is sized for the room and ducted outdoors, not into the attic. The exhaust fan is checked for size and duct route, and replaced or rerouted if it does not vent outside. Dimmers let one fixture serve for both bright tasks and a soft bath. Humidity-sensing switches turn the fan on when needed. A timer switch can keep the fan running after you leave the room.
Expect about $520–$1,500 for a lighting package in Bloomington. A typical fixture package with basic installation. Whole-house electrical, panel upgrades and designer statement fixtures are not included.
Checked before work begins


A walk-in tub lets a Bloomington homeowner open a door, sit down and bathe without climbing over a high tub wall.
Expect about $2,700–$15,900 for the project in Bloomington. Basic to mid-feature walk-in tub, installed. Ultra-premium packages are extra; we make no claims about medical coverage.
We measure the alcove, doorways and hallways, check the floor and confirm hot water and electrical needs before ordering. The old tub is removed, the new unit is set level and connected, and the door seal is tested. Controls are placed within reach from the seat, and a non-slip floor and grab bars are planned for the area outside the tub. We size the tub to the existing alcove where possible to limit plumbing and framing changes. We show you how to operate the door, controls and drain at handover. Units with jets or heaters often need a dedicated GFCI circuit. The surround is finished to keep water out of the wall.
Census figures put the median age in Bloomington at 32.9. Walk-in tubs are chosen for many reasons, from a relative's mobility to planning ahead; in every case we check the water heater size and the door widths along the route before a model is picked.
On our list
Whether a home in Bloomington is on sewer or septic depends on the parcel. Septic systems fall under San Bernardino County Environmental Health Services, so before a toilet is relocated we confirm the system and plan the drain run to suit it.
A new toilet is one of the simplest upgrades in a Bloomington bathroom, provided the flange and floor are sound.
Comfort-height bowls sit a few inches higher than standard ones, and elongated bowls need more space in front. We check the clearance to walls, the tub and the vanity before choosing. Bidet seats need an outlet nearby, which is easier to add while other work is going on. The new toilet is bolted, sealed and tested for leaks before we leave. The old toilet is removed and disposed of as part of the job. Skirted toilets with hidden trapways are simpler to clean. Water-saving models are standard now, and many flush well. We add a new seal, supply line and shutoff valve as part of the job. The supply line is replaced with a braided line rather than reused.
Budget $260–$820 per installed toilet in Bloomington. Covers a standard or mid-range toilet installed in the same location. Luxury smart or bidet units and drain relocations cost more.
Before we start


The median home in Bloomington was built in 1975. A small bathroom of that age can have tired wiring, an old fan or a patched subfloor; we open up and check before finalizing the layout, so the plan reflects what is actually behind the walls.
Small bathrooms in Bloomington can feel larger with the right layout, lighter finishes and storage built into the walls.
Every inch counts, so we look at a narrower or wall-mounted vanity, a corner shower, or a tub-shower combination. Clear glass instead of a curtain makes the room feel larger. Recessed shelves and medicine cabinets add storage without bulk. Large tiles and a single floor finish keep the room visually calm. Light-colored walls and good lighting help. We start with a scale drawing of the room and test where the toilet, sink and shower or tub can fit. A smaller-footprint toilet can add a few inches of clearance. Ventilation is checked carefully, since moisture builds quickly in a small space. Mirrors and lights are placed to brighten the whole room, not just the sink. Towel hooks take less wall space than towel bars.
Expect about $5,000–$12,000 for the project in Bloomington. Powder rooms and compact full baths. Primary-suite spa remodels and commercial work are not included.
Planning checklist
In Bloomington homes we install vanities between 24" and 72" wide. The table shows how each width is usually used; your final size comes from measuring the wall.
| Size | Configuration | Good Fit For |
|---|---|---|
| 24" | Doors only | Tight half baths |
| 27" | Doors only | Compact guest bathrooms |
| 30" | Doors with drawers | A single sink with useful storage |
| 33" | Doors only | Uncluttered medium bathrooms |
| 36" | Bank of 3 drawers, left or right | Single sink with plenty of drawers |
| 48" | Bank of 3 drawers, left or right | Larger single-sink layouts |
| 60" | Single or double sink | Compact double vanity |
| 72" | Single or double sink | Two sinks and long counter |
The estimate visit settles the width with a tape measure.
Things we check for every Bloomington bathroom before work is booked.
Bloomington sits at about 1,058 feet. We note access, parking and the nearest supply route when planning the work schedule.
About 8.3% of homes in Bloomington are mobile homes, according to the Census. If yours is a manufactured home, permits for HCD-regulated units follow state rules, so we confirm the construction type first.
Bloomington is served by I-10. We plan deliveries and debris hauling around that route.
We start with what bothers you about the room and when work can happen.
Measurements, a plumbing check and a look at the subfloor set the scope.
Fixtures and finishes are picked to fit the room and the budget.
Permit applications and inspection scheduling when the work requires them.
Tear-out comes first, then pipes and waterproofing.
Our crew installs the new floor, fixtures and finishes.
A walkthrough with you and a punch list before sign-off.
Styles we build in San Bernardino County homes, including Bloomington.






Installers on our own payroll.
Permits handled with the correct building office.
Fixtures chosen after reading the local water report.
One person to call from start to finish.
An itemized price agreed in advance.
Vanity width set by measurement.
Bathroom remodeling in neighboring areas.
Request an estimate and we will come measure and price the job.
Share a few details and we will call to set a time.
Bathtub installation in Bloomington depends on the tub type, whether the drain and supply lines can stay in place, the wall surround, waterproofing, and repairs discovered after removal. Compare the planning range in the bathtub section above with an estimate based on your actual bathroom; a like-for-like replacement and a layout change are not the same job.
Shower remodeling costs in Bloomington depend on shower size, tile and waterproofing work, the type of glass enclosure, plumbing and valve changes, and any damage behind the old walls. Keeping the existing shower footprint may reduce the amount of plumbing work. Use the shower section above for its planning range, then compare written scopes rather than only the final price.
A tub-to-shower conversion in Bloomington is priced according to demolition, drain position, shower base and waterproofing, wall finishes, glass, and any required plumbing changes. A curbless entry or new shower layout may change the work involved. Review the planning range above, and ask the estimator to identify what is included before approving the conversion.
Replacing a shower with a bathtub in Bloomington may require checking whether the space fits the selected tub, relocating the drain or water lines, and installing a suitable surround and waterproofing. The tub model, access for installation, and condition of the subfloor can affect the scope. The planning range above is a starting point; an on-site assessment is needed for a project-specific quote.
A small bathroom remodel in Bloomington can include a compact vanity, a tub or shower upgrade, flooring, lighting, and ventilation. Costs change with how much tile is replaced, whether fixtures move, and whether hidden moisture damage needs repair. Use the small-bathroom planning range above, then choose the updates that improve clearance, storage, and everyday use.
For homes in unincorporated Bloomington, San Bernardino County Building and Safety generally handles permits. Plumbing alterations, new electrical work, and significant bathroom changes often need approval; finish-only work may be treated differently. Confirm the property jurisdiction and the proposed scope with the permitting authority before work begins.
Confirm the water provider for your Bloomington address on the latest water bill; the utility information in the shower remodeling section above is a starting point. Review that provider’s current water-quality report to understand mineral content and choose fixtures and glass finishes that are practical to maintain.
Timing for a bathroom remodel in Bloomington depends on whether fixtures stay in place, how much plumbing or tile work is needed, material lead times, and any required inspections. If the home has only one working bathroom, discuss access and the work sequence during planning. Ask for a written schedule after the scope and materials are agreed.
The age and condition of a Bloomington home can affect bathroom remodeling if existing plumbing, ventilation, electrical work, or waterproofing needs attention. Older finishes do not automatically mean hidden damage. Ask for an assessment of accessible components, and document any newly discovered repair work before changing the project scope.
See the vanity size table above for the widths we install; we set your size from the wall measurement at the free estimate.
Use the request form on this page or call (909) 494-5343 to discuss your Bloomington bathroom project. Share the room’s approximate size, which fixtures you want to change, and any known damage or layout concerns. Ask what the written estimate includes before deciding on the work.