Our in-house team remodels Rialto bathrooms, whether the job is a toilet swap, a shower rebuild or a room taken down to the studs.
From the first sketch to the last fixture, one team runs the project.
A Rialto bathroom project begins with what bothers you about the room now, then a measured plan for the wet area, storage and fixtures.
Plumbing, electrical and layout work in Rialto is permitted through City of Rialto Building & Safety / Community Development. Waterproofing, fixtures and finishes are spelled out in the scope before demolition.
No pressure, no obligation. We'll call to confirm your appointment window.
Each service below is performed for Rialto homeowners by our in-house crew, with a planning price range for each service.
A tub replacement in Rialto can keep the same alcove while the model, depth and wall finish all change in the same visit.
We begin by measuring the opening and noting the drain side, since tubs are made for left or right drains. The old tub is cut or lifted out without damaging nearby walls where possible. In every case we check the framing under the tub, confirm the overflow and drain size, and set the tub before any wall finish goes up so the joint stays watertight. Ledger boards under the tub flange give the edge solid support. Freestanding tubs need a floor-mounted or wall-mounted filler planned before tile. The tub shoe and drain linkage are replaced rather than reused.
The planning range in Rialto is $1,300–$3,500 for the project. Professional tub replacement for common alcove and freestanding models. Excludes premium stone tubs, materials-only purchases and full remodel totals.
Census ACS 2020–2024 estimates put 76% of the housing in Rialto in buildings from before 1990. California Civil Code Section 1101 requires water-conserving fixtures in homes built before 1994, and a permitted remodel is when that is checked, so older toilets, showerheads and faucets are noted in your tub estimate up front.
Planning checklist


The water supplier in Rialto is the City of Rialto or West Valley Water District, depending on the parcel. Its yearly water quality report guides the showerhead, valve and finish we suggest for your house.
Updating a shower in Rialto can mean new walls and glass only, or a full rebuild with a new pan, valve and drain.
Behind every tiled wall sits a waterproof layer: a sheet membrane, a liquid-applied membrane or a foam board system. The floor is sloped to the drain, either with a mortar bed or a pre-formed tray, and flood tested before tile. Tile choices affect slip resistance, grout upkeep and cost, so we compare a few. Shower glass is ordered after tile so it is measured on the finished surfaces. Corner shelves can be built into the tile instead of added later. Shower niches are framed between studs so they do not weaken the wall. Valves are chosen for steady temperature, and fixtures are picked so the trim matches the rough-in.
Budget $4,500–$12,000 for the project in Rialto. Covers shower remodels from simple ready-made replacements to custom tiled showers. A full bathroom gut is priced separately unless the work stays inside the shower.
Before we start
If you shower daily and seldom bathe, the tub space in a Rialto home can work better as a walk-in shower.
Conversions run in a set order: demolition, plumbing changes, framing for niches and blocking, waterproofing, flood test, tile, then glass. The drain position and curb height are the two choices that move the price most. A low curb keeps costs down; a curbless entry needs the floor recessed and a linear drain. Grab bar blocking, a niche and a bench can be framed in while the walls are open. Old tub wall tile is removed down to the studs so the new waterproofing is continuous. If the alcove is long, a bench at one end can use the extra length. The new valve is placed so you can reach it before stepping under the water.
Households in Rialto average 3.8 people. When several people share one bathroom each morning, a walk-in shower with a wide opening, a niche for each person's bottles and a fixed glass panel can be easier to share than a tub-shower combination.
The planning range in Rialto is $3,500–$10,000 for the tub-to-shower conversion. Covers tub removal and a new shower, ready-made to common custom. Wet-room luxury builds and full remodels are excluded.
Before we start


About 66% of occupied homes in Rialto are owner-occupied. If you plan to stay and want a tub back, for small children or for soaking, we check that the water heater can fill a deeper tub before choosing the model.
Putting a tub where a shower stood gives a Rialto bathroom more flexibility, since a tub with a shower head serves both uses.
We plan the conversion around the drain first, since that is the part that most often changes. Then we choose the tub material and depth, confirm the floor framing can carry a filled tub, and select the wall finish. A deeper tub needs more hot water to fill, so we check the heater size. A combination tub and shower setup keeps a standing shower available after the conversion. The valve is lowered for tub use and can keep a shower head above. We measure the old stall to see which fits or whether a wall must move. A tub with an integral apron saves building a separate front panel.
Plan on $2,600–$9,400 for the shower-to-tub conversion in Rialto. Includes removal, framing and typical plumbing to fit a tub. Major structural work and premium freestanding models fall outside this range.
What we check first
Floor choices for Rialto bathrooms come down to grip when wet, comfort underfoot, the height at the door and the subfloor.
Budget $8–$26 per square foot installed in Rialto. Per-square-foot price for the finished floor, installed. Excludes shower waterproofing, the vanity and full remodel totals.
Choosing a bathroom floor means weighing grip, comfort, upkeep and how the floor meets the hallway. Porcelain is tough and water-resistant; vinyl plank is softer and quicker to lay. On slabs we check for cracks that could transfer. Plank flooring is laid with sealed seams and an expansion gap hidden under trim. Natural stone needs sealing, while porcelain does not. Tile is laid from a centered line so the edges are even on both sides. Matte finishes give better grip than polished ones when wet. Baseboard or tile base is installed after the floor to cover the edge gap. Grout lines can be kept narrow on rectified tile for a calmer look.
The average daily low at the Redlands weather station is about 51°F (NOAA 1991–2020). Floor heat is optional here; what matters more is a tile or plank with good wet grip and a subfloor checked for soft spots before it is covered.
Checked before work begins


Vanity choices in Rialto start with who uses the room and what needs to be stored there.
A new vanity can add drawers in place of doors, pull-out organizers, or an outlet inside a drawer for tools that stay plugged in. Wall-mounted vanities need solid blocking between the studs. Undermount sinks are easiest to wipe clean, while vessel sinks need a lower cabinet. Lights and mirrors are centered on the sinks once the cabinet position is fixed. Countertop choice affects cost and upkeep. A backsplash height is chosen to match the faucet and outlet locations. Double sinks need more width and a second drain. Toe-kick lighting can be added under a floating vanity. The drain and supply lines are checked for leaks after the sink is set. We shut off water, remove the old vanity and top, and check the wall and floor behind it.
Parking and dumpster placement rules can differ from street to street in Rialto. We confirm where the delivery truck and any dumpster can sit before the vanity arrives, so install day starts on time.
The planning range in Rialto is $800–$3,000 per vanity installed. One vanity supplied and installed, ready-made to semi-custom, including top and faucet hookup. Full custom millwork is outside this range.
Planning checklist
A lighting update in Rialto pairs new fixtures with a fan that actually clears moisture from the room.
A bathroom lighting plan layers general, task and night light. We choose fixtures and color temperature to suit the finishes, place sconces or a light bar at the mirror, and add a wet-rated light in the shower. GFCI protection, fan-light combinations and switch heights are confirmed with you before we wire anything. Fan and light can be on separate switches so the fan runs longer. The exhaust fan is sized for the room and ducted outdoors, not into the attic. A timer switch can keep the fan running after you leave the room. Dimmers let one fixture serve for both bright tasks and a soft bath.
Every bathroom outlet needs GFCI protection by California code, light fixtures by the tub or shower need a damp or wet rating, and CALGreen expects a humidity-controlled fan exhausting outdoors. With about 12.9 inches of yearly precipitation at the Redlands station, outdoor weather matters less than daily steam, so fan capacity follows the room and the lights are placed as one layout.
Budget $520–$1,600 for a lighting package in Rialto. Fixtures and basic install for a typical bathroom. Whole-house electrical, panel upgrades and designer statement fixtures are not included.
On our list


A walk-in tub in Rialto replaces the climb over a tub wall with a low step and a built-in seat.
Budget $2,700–$16,100 for the project in Rialto. Basic to mid-feature walk-in tub, installed. Premium feature bundles are excluded, and no medical-coverage claims are made.
Walk-in tubs are taller and heavier than standard ones, so we measure every doorway and turn on the delivery path. The floor is checked for its ability to carry a full tub with a person in it. Grab bars, a handheld shower and slip-resistant flooring around the tub complete the install. Grab bars are placed where they help both entry and standing. The door seal is inspected for a tight fit before the first fill. We size the tub to the existing alcove where possible to limit plumbing and framing changes. Hand-held showers can be mounted at the tub for rinsing while seated. Jets and heaters can need a dedicated circuit. Because the bather sits inside while the tub fills and drains, fast-fill faucets and quick-drain pumps make a real difference.
The Census reports a median age of 32.6 in Rialto. A walk-in tub comes as a single bulky unit, so before ordering we measure the hallways and door openings it must pass through and confirm the water heater can fill it.
On our list
A toilet replacement in Rialto is a short job, but rough-in, flange and floor condition decide which models will fit well.
Rialto homes are primarily on sewer. Even so, moving a toilet means a new drain run with the right slope and venting, so we check the existing line and flange before choosing the new location.
Toilet choice covers bowl height, shape, flush performance and how easy it is to clean. We confirm the rough-in and the space in front and to the sides. We test the flush and check for leaks at the base and tank. A new wax-free seal is an option instead of a traditional wax ring. We add a new seal, supply line and shutoff valve as part of the job. We level the toilet with shims rather than relying on the seal. The old toilet is removed and disposed of as part of the job. Elongated bowls need more clearance in front than round bowls. A skirted bowl hides the trapway and is easier to wipe clean.
On our list
The planning range in Rialto is $260–$830 per installed toilet. Supply and install on the current rough-in. High-end smart or bidet toilets and rough-in relocation are not included.


Remodeling a small bathroom in Rialto is about using every inch of wall and floor without crowding the room.
Half the homes in Rialto were built before 1982, according to Census figures. In a small room, we look at the fan, wiring and subfloor first, then draw a layout that keeps plumbing in place unless moving it clearly gains space.
We start with a scale drawing of the room and test where the toilet, sink and shower or tub can fit. Keeping plumbing in place controls cost, but a small move can sometimes free a lot of space. Light-colored walls and good lighting help. Ventilation matters more in a small bathroom, because moisture has less room to spread. Recessed shelves and medicine cabinets add storage without bulk. Large tiles and a single floor finish keep the room visually calm. Towel hooks take less wall space than towel bars. We plan door swing so it does not hit the toilet or vanity. A corner sink or a shallow vanity can free up the walkway.
What we check first
Expect about $5,000–$12,000 for the project in Rialto. Covers small bathroom remodels from powder rooms to compact full baths. Primary-suite spa remodels and commercial work are not included.
In Rialto homes we install vanities between 24" and 72" wide. The table shows how each width is usually used; your final size comes from measuring the wall.
| Size | Configuration | Good Fit For |
|---|---|---|
| 24" | Doors only | Half baths and narrow walls |
| 27" | Doors only | Compact guest bathrooms |
| 30" | Doors with drawers | Everyday single-sink storage |
| 33" | Doors only | Clean look for a medium bathroom |
| 36" | Bank of 3 drawers, left or right | Single sink with plenty of drawers |
| 48" | Bank of 3 drawers, left or right | Larger single-sink layouts |
| 60" | Single or double sink | Smallest practical double vanity |
| 72" | Single or double sink | Long primary-suite walls |
The estimate visit settles the width with a tape measure.
Notes we review with Rialto homeowners before a bathroom project is scheduled.
Rialto sits at about 1,346 feet. We note access, parking and the nearest supply route when planning the work schedule.
About 7.9% of homes in Rialto are mobile homes, according to the Census. If yours is a manufactured home, permits for HCD-regulated units follow state rules, so we confirm the construction type first.
Rialto has condos and townhomes as well as houses. Where a bathroom shares a wall or drain stack with a neighbor, we check association approval before plumbing changes.
A first conversation about goals, timing and the room's limits.
We take measurements and check what is under the floor and behind the walls.
We narrow fixture and finish options to what fits.
Permits and inspections arranged when the scope calls for them.
Careful removal of old fixtures, then plumbing and waterproofing rough-in.
Floor, vanity, tub or shower and trim go in.
A final walkthrough together before the job is closed out.
Bathroom styles from our San Bernardino County work, Rialto among them.






A crew that works only for us.
The right permit office for your address.
Fixture picks that account for your water report.
A single contact from estimate to walkthrough.
Itemized pricing agreed before the start date.
Vanity sizes taken from your measured wall.
Other communities near Rialto where we remodel bathrooms.
Ask for a visit and get a measured, itemized price for your bathroom.
Send a short note about the room and we will get back to you.
Bathtub installation in Rialto depends on the tub type, whether the drain and supply lines can stay in place, the wall surround, waterproofing, and repairs discovered after removal. Compare the planning range in the bathtub section above with an estimate based on your actual bathroom; a like-for-like replacement and a layout change are not the same job.
Shower remodeling costs in Rialto depend on shower size, tile and waterproofing work, the type of glass enclosure, plumbing and valve changes, and any damage behind the old walls. Keeping the existing shower footprint may reduce the amount of plumbing work. Use the shower section above for its planning range, then compare written scopes rather than only the final price.
A tub-to-shower conversion in Rialto is priced according to demolition, drain position, shower base and waterproofing, wall finishes, glass, and any required plumbing changes. A curbless entry or new shower layout may change the work involved. Review the planning range above, and ask the estimator to identify what is included before approving the conversion.
Replacing a shower with a bathtub in Rialto may require checking whether the space fits the selected tub, relocating the drain or water lines, and installing a suitable surround and waterproofing. The tub model, access for installation, and condition of the subfloor can affect the scope. The planning range above is a starting point; an on-site assessment is needed for a project-specific quote.
A small bathroom remodel in Rialto can include a compact vanity, a tub or shower upgrade, flooring, lighting, and ventilation. Costs change with how much tile is replaced, whether fixtures move, and whether hidden moisture damage needs repair. Use the small-bathroom planning range above, then choose the updates that improve clearance, storage, and everyday use.
For homes within the City of Rialto, the local building department is the place to confirm bathroom permit requirements. Moving plumbing, altering electrical work, or making other substantial changes often needs a permit, while some finish-only updates may not. Check the exact address and work scope before starting; do not assume every bathroom update follows the same rule.
Confirm the water provider for your Rialto address on the latest water bill; the utility information in the shower remodeling section above is a starting point. Review that provider’s current water-quality report to understand mineral content and choose fixtures and glass finishes that are practical to maintain.
Timing for a bathroom remodel in Rialto depends on whether fixtures stay in place, how much plumbing or tile work is needed, material lead times, and any required inspections. If the home has only one working bathroom, discuss access and the work sequence during planning. Ask for a written schedule after the scope and materials are agreed.
Often, a bathroom in Rialto can be updated without moving its main fixtures. Keeping the toilet, sink, and shower drains in their existing positions may limit plumbing changes. Before deciding, check clearances, ventilation, accessibility needs, and whether the new fixtures fit the current footprint.
See the vanity size table above for the widths we install; we set your size from the wall measurement at the free estimate.
Use the request form on this page or call (909) 494-5343 to discuss your Rialto bathroom project. Share the room’s approximate size, which fixtures you want to change, and any known damage or layout concerns. Ask what the written estimate includes before deciding on the work.